Brookfield DV-III Ultra Rheometer Uživatelský manuál stáhnout pdf (Strana 12)

Brookeld Engineering Laboratories, Inc. Page 12 Manual No. M98-211-E0912

1) Place the upright rod into the hole at the front of the base. The rack gear and clamp assembly

should face the rear of the base (see Figure I-4). The upright rod (item #1) is held in place

with the jam nut (item #4) which is attached from the bottom of the base. Tighten this nut

with a suitable wrench (spanner).

DV-III Ultra Stand Assembly

CLAMP ASSEMBLY

NOTE: “FRONT” FACES TOWARD YOU.

DV-III Ultra

HEAD UNIT

TENSION SCREW

Figure I-4

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 132 133

BROOKFIELD DV-III ULTRA 1
Table of Contents 3
I. INTRODUCTION 5
Maximum Torque Value 6
Component Part Number 7
Ball Bearing Option: 10
Electrical Certication: 10
CLAMP ASSEMBLY 12
DV-III Ultra 12
HEAD UNIT 12
TENSION SCREW 12
Connector 14
RS-232 Serial 14
Printer/Computer 14
STRIP CHART RECORDER 16
II. GETTING STARTED 18
“REMOVE SPINDLE, LEVEL 18
KEY.” Press a key 18
TORQUE LESS THAN 0% 21
SELECT SPDL key. The DV-III 21
MOTOR ON/OFF/ESCAPE key 21
one minute. 150 seconds 32
USE SET:_ 33
STEP TIME = 00:05 33
USING PREPROGRAMMED SPEEDS 37
OPTION/TAB key 38
LOCKOUT OPTIONS 38
PROG RUN key is pressed 40
PROG RUN 40
ENTER key. Assume that the 41
ENTER key, our display will 41
PROGRAMMED SPEED STOP 41
PROGRAMMED SPEED HOLD 42
SINGLE SPEED 49
DVIII SPEED/TIME PAIRS 50
B.E.V.I.S. PROGRAMS 50
STANDARD CASSON PRINTOUT 51
1. Casson (Standard) 52
3. Bingham Plastic 52
4. Power Law 53
5. IPC Paste Analysis 53
Figure IV-44: Test Screen 55
Figure IV-45: Run/Data Screen 55
Figure IV-46: Setup Screen 56
Figure IV-47: Analysis Screen 56
Figure IV-48 57
= shear stress 58
Figure IV-65 79
V. OPTIONS 89
ENTER key 89
V.4 Set Temperature 91
V.6 Timed Data Collection 93
Do Not hit the 96
CONE with the CUP! 96
A.3 SETTING THE GAP 97
Universal Spindle Ranges 99
Rheometer at 45 RPM 100
Spindle Speed = 45 RPM 100
RHEOLOGICAL PROPERTIES 105
Table D-1 (continued) 108
(S x T) 112
+/-) 0.1°C 114
°C, are shown in Table E-1 114
Table E-1 115
°C, 93.3°C, 149°C 115
Table E-2 115
+ 500) cP = (+/-) 622.57 cP 119
Figure F-1 121
DV-III Ultra Stand Assembly 122
Item Part # Description Qty 122
4 hex digits. Calculate the 125
Zero offset = tval/100 125
VISCOSITY TEST REPORT 133

Komentáře k této Příručce

Žádné komentáře

Brookfield DV-III Ultra Rheometer Uživatelský manuál Strana 12

Komentáře k této Příručce

Související produkty a manuály pro Měřící nástroje Brookfield DV-III Ultra Rheometer